You can see a TTL pin with 3VR, 3VT, 5Vr, 5VT, VCC and GND on your sim900a near your power supply pin. You have to connect GSM's 5VT to Arduino D9 and GSM's 5VR to Arduino's D10 for serial communication between arduino and sim900a module.
SoftwareSerial is a library of Arduino which enables serial data communication through other digital pins of Arduino. The library replicates hardware functions and handles the task of serial communication. To be able to interface gsm module with arduino, you will have to download this library and extract it into your Arduino's libraries.
Gsm Sim900 Datasheet Pdf Download
Hi, i used your code as it is, but hangup and receive calls successfully have done but not sending sms and other. Shall i know whats the cause. please help me in this./*THIS TUTORIAL USED GSM SIM900A MINI V3.9.2 Connect 5VT to D9 and 5VR to D10 Feed GSM SIM900A with Arduino's 5V Code by IDAYU SABRI - MYBOTIC*/#include SoftwareSerial mySerial(9, 10);//tx, rxchar msg;char call;void setup() mySerial.begin(9600); // Setting the baud rate of GSM Module Serial.begin(9600); // Setting the baud rate of Serial Monitor (Arduino) Serial.println("GSM SIM900A BEGIN"); Serial.println("Enter character for control option:"); Serial.println("h : to disconnect a call"); Serial.println("i : to receive a call"); Serial.println("s : to send message"); Serial.println("r : ReceiveMessage"); Serial.println("c : to make a call"); Serial.println("e : to redial"); Serial.println(); delay(100);void loop() if (Serial.available()>0) switch(Serial.read()) case 's': SendMessage(); break; case 'r': ReceiveMessage(); break; case 'c': MakeCall(); break; case 'h': HangupCall(); break; case 'e': RedialCall(); break; case 'i': ReceiveCall(); break; if (mySerial.available()>0) Serial.write(mySerial.read());void SendMessage() Serial.println("Sending Message"); mySerial.println("AT+CMGF=1"); //Sets the GSM Module in Text Mode delay(1000); // Delay of 1000 milli seconds or 1 second mySerial.println("AT+CMGS=\"+917799036041\"\r"); // Replace x with mobile number +91 delay(1000); mySerial.println("sim900a sms");// The SMS text you want to send delay(100); mySerial.println((char)26);// ASCII code of CTRL+Z delay(1000);void ReceiveMessage() Serial.println("Received Message"); mySerial.println("AT+CNMI=2,2,0,0,0"); // AT Command to recieve a live SMS delay(1000); if (mySerial.available()>0) msg=mySerial.read(); Serial.print(msg); void MakeCall() mySerial.println("ATD+917799036041;"); // ATDxxxxxxxxxx; -- watch out here for semicolon at the end!! Serial.println("Calling "); // print response over serial port delay(5000);void HangupCall() mySerial.println("ATH"); Serial.println("Hangup Call"); delay(1000);void ReceiveCall() mySerial.println("ATA"); Serial.println("Received Call"); delay(1000); call=mySerial.read(); Serial.print(call); void RedialCall() mySerial.println("ATDL"); Serial.println("Redialing"); delay(1000);
I have succeeded in this project using Arduino Mega.To those whom not yet get it, here is the tips.1. Coding is Good. No need to Worry about That.2. Need Extra power Supply. For me, I use power supply unit of 5V to Vin (Arduino Mega)3. I use pin 2 and 3 for 5VT and 5VR (remember to change it in coding).Remember, TX (Arduino) goes to RX (sim900a) and vice versa. (i think they don't mention that in here) Done.Email me if you guys don't understand. Ill help.
Nice work guys, keep it upI wanted to ask could you please help me to sending my sensor data over the internet? I wanted to transmit my data using internet and gsm module, I did it using esp8266 but now I wanted to transmit using gsm sim900 shield.Thanks in advance
Hi.I think this issue provides information about your question: stackoverflow.com/questions/63240900/sim900-gsm-module-how-to-check-if-the-outgoing-call-is-answeredI hope this helps.Regards,Sara
The module SIM900A has multiple pins but all of them have some hardware requirement that is available in the datasheet. There is a bunch of predesigned board which solves the requirement of the hardware. To use the module connect it with the Arduino like the given circuit.
This library is archived and is no longer being maintained. It can be still be downloaded and used, but is read-only and cannot be contributed to. For more information, you can view this repository on GitHub.
Q2: Please download the firmware "SIM_900_AGPS_instructions" from Resource module on the wiki,if you have any problem of software or hardware.And this latest one can support HTTPS ,etc.More information please refer to the introduction within.
2ff7e9595c
Komentarze